ArticleACS omega2025
A Denture Base Resin Developed Using Hyperbranched Polyurethane Acrylate, Tricyclodecane Dimethanol Diacrylate, and Liquid Crystal Display-Based Three-Dimensional Printing.
Article in ACS omega, 2025. The graph could read no effect estimate from its abstract, so it casts no vote on the map. Not yet cited in PubMed.
What it found
Each row is one number read from the abstract, on the scale the paper reported it, with its interval. Left of the dashed line favours the treatment, right favours the comparator. Under each row is the sentence it came from. New to these charts? A ten-minute tutorial.
The abstract states no effect estimate the extractor could read, or names no intervention and outcome on the map, so this paper lights no cell and moves no belief. It is still indexed, cited and linked below.
The trial behind it
Trials whose registry record cites this paper, or whose number appears in the abstract. A trial that started after this paper was published is citing it as background, not reporting it.
Neither the registry nor the abstract names a trial number. If this is a trial report, that itself is worth knowing.
Who cites it
0 citing papers in PubMed.
No citing paper in PubMed yet.
Corrections and comments
PubMed lists nothing against this paper. Absence here is not a guarantee, only a check that was made.
Authors and funding
8 authors.
Funding
No grant is acknowledged in the PubMed record.
Abstract
Poly-(methyl methacrylate) (PMMA) is the most widely used denture base material. However, because of PMMA's insufficient mechanical strength, fracture is a frequent problem after long-term denture use for chewing. In this study, hyperbranched polyurethane acrylate (HBPUA) was synthesized using trimethylolpropane, isophorone diisocyanate, and hydroxyethyl acrylate in a molar ratio of 1:3.1:3.2. Gel permeation chromatography revealed that the number- and weight-average weights of the synthesized HBPUA were approximately 1325 and 1797, respectively. For blended resins comprising different HBPUA and tricyclodecane dimethanol diacrylate (TCDDMDA) weight ratios, viscosity increased with increasing HBPUA content. A composition of 10 and 90 wt % HBPUA and TCDDMDA (TC10), respectively, was optimal for developing a denture base resin using liquid crystal display-based three-dimensional (3D) printing. Resins exposed to light for 5, 15, and 30 s and containing photoinitiator concentrations of 1 and 2 mol % were fabricated for comparison with a commercial resin, Denture 3D+. Attenuated total reflectance Fourier-transform infrared spectroscopy revealed that Denture 3D+ possessed a higher double bond conversion rate than those of the TC10 materials. Three-point bending tests revealed that Group 4 (TC10-0.01, 15 s) possessed the highest flexural strengths after both 50 h and 28 d of water immersion and that this group's flexural modulus also exceeded that of Denture 3D+, although the group's toughness and elongation were lower than those of Denture 3D+. In addition, the water sorption and solubility, surface roughness, and volumetric shrinkage of TC10 materials were lower than those of Denture 3D+. Furthermore, the impact strength, microhardness, and biocompatibility of Group 4 were comparable to those of Denture 3D+. These results indicate that Group 4 not only satisfied the ISO 20795-1 requirements but also possessed some properties superior to those of Denture 3D+, implying strong potential for practical application as a denture base material.
Identifiers
What OpenQuestion holds
Registered trials
Read under generation 80e0d062 · epoch 390. Bibliography from PubMed, PubMed Central and OpenAlex; grants from NIH RePORTER; trial links from ClinicalTrials.gov; estimates, votes and beliefs from the OpenQuestion graph.