Evidence map›Paper›PMID 39771629›Full record

ArticleSensors (Basel, Switzerland)2024

The Influence of Polylactic Acid Filament Moisture Content on Dust Emissions in 3D Printing Process.

Anna Karwasz, Filip Osiński, Weronika Kaczmarek, Kacper Furmaniak, Izabela Rojek

Abstract read
PubMed Full text at PMC Publisher
In one paragraph

Article in Sensors (Basel, Switzerland), 2024. The graph could read no effect estimate from its abstract, so it casts no vote on the map. Cited by 1 paper.

0numbers the graph read from it
0cells of the map it votes in
1citing papers in PubMed
–field-weighted citation impact
1 · What the graph read from it

What it found

Each row is one number read from the abstract, on the scale the paper reported it, with its interval. Left of the dashed line favours the treatment, right favours the comparator. Under each row is the sentence it came from. New to these charts? A ten-minute tutorial.

The abstract states no effect estimate the extractor could read, or names no intervention and outcome on the map, so this paper lights no cell and moves no belief. It is still indexed, cited and linked below.

2 · The registry

The trial behind it

Trials whose registry record cites this paper, or whose number appears in the abstract. A trial that started after this paper was published is citing it as background, not reporting it.

Neither the registry nor the abstract names a trial number. If this is a trial report, that itself is worth knowing.

3 · Its place in the literature

Who cites it

1 citing paper in PubMed.

  1. Article
4 · The record

Corrections and comments

PubMed lists nothing against this paper. Absence here is not a guarantee, only a check that was made.

5 · Who and what money

Authors and funding

5 authors.

Anna KarwaszFaculty of Mechanical Engineering, Poznan University of Technology, Piotrowo 3, 60-138 Poznań, Poland.ORCID 0000-0002-7276-681X
Filip OsińskiFaculty of Mechanical Engineering, Poznan University of Technology, Piotrowo 3, 60-138 Poznań, Poland.ORCID 0000-0003-0716-8546
Weronika KaczmarekFaculty of Mechanical Engineering, Poznan University of Technology, Piotrowo 3, 60-138 Poznań, Poland.
Kacper FurmaniakFaculty of Mechanical Engineering, Poznan University of Technology, Piotrowo 3, 60-138 Poznań, Poland.
Izabela RojekFaculty of Computer Science, Kazimierz Wielki University, Chodkiewicza 30, 85-064 Bydgoszcz, Poland.ORCID 0000-0002-9958-6579

Funding

The presented results are derived from a scientific statutory research project number 0613/SBAD/4770 conducted by Faculty of Mechanical Engineering, Poznan University of Tech-nology, Poland, supported by the Polish Ministry of Science and Higher Education The presented results are derived from a scientific statutory research project number 0613/SBAD/4770 conducted by Faculty of Mechanical Engineering, Poznan University of Tech-nology, Poland, supported by the Polish Ministry of Science and Higher Education
6 · The paper itself

Abstract

This paper presents the results of a study on the effect of moisture content in polylactic acid (PLA) filaments on dust emissions during incremental manufacturing. The tests were conducted in a customised chamber using a standard 3D printer, and Plantower PMS3003 sensors were used to monitor air quality by measuring PM1, PM2.5 and PM10 concentrations. The filament humidity levels tested were 0.18%, 0.61% and 0.83%. The results show that a higher moisture content in the filament significantly increases dust emissions. For dry filaments (0.18% humidity), the average dust emissions ranged from 159 to 378 µg/m

Indexed as

additive manufacturingdust emissionsfilament moisturelaser dust sensorsPLA

Identifiers

PMID39771629
PMCPMC11678983

What OpenQuestion holds

Textmetadata
LicenceCC BY
Read underepoch 390

Registered trials

None linked

Read under generation 80e0d062 · epoch 390. Bibliography from PubMed, PubMed Central and OpenAlex; grants from NIH RePORTER; trial links from ClinicalTrials.gov; estimates, votes and beliefs from the OpenQuestion graph.