Evidence map›Paper›PMID 39730705›Full record

ArticleScientific reports2024

3D printing of continuous cotton thread reinforced poly (lactic acid).

Xiaohui Song, Yishen Ye, Shifeng Huang, Xingguo Han, Zhouping Huang, Wenfang Guan, Zhengwei Yang, Minggan Wang

Abstract read
PubMed Full text at PMC Publisher
In one paragraph

Article in Scientific reports, 2024. The graph could read no effect estimate from its abstract, so it casts no vote on the map. Cited by 3 papers.

0numbers the graph read from it
0cells of the map it votes in
3citing papers in PubMed
–field-weighted citation impact
1 · What the graph read from it

What it found

Each row is one number read from the abstract, on the scale the paper reported it, with its interval. Left of the dashed line favours the treatment, right favours the comparator. Under each row is the sentence it came from. New to these charts? A ten-minute tutorial.

The abstract states no effect estimate the extractor could read, or names no intervention and outcome on the map, so this paper lights no cell and moves no belief. It is still indexed, cited and linked below.

2 · The registry

The trial behind it

Trials whose registry record cites this paper, or whose number appears in the abstract. A trial that started after this paper was published is citing it as background, not reporting it.

Neither the registry nor the abstract names a trial number. If this is a trial report, that itself is worth knowing.

3 · Its place in the literature

Who cites it

3 citing papers in PubMed.

  1. Article
  2. Review
  3. Article
4 · The record

Corrections and comments

PubMed lists nothing against this paper. Absence here is not a guarantee, only a check that was made.

5 · Who and what money

Authors and funding

8 authors.

Xiaohui SongKey Laboratory of Special Engineering Equipment Design and Intelligent Driving Technology, Guilin University of Aerospace Technology, Guilin, 541004, China. songxiaohui2010@163.com.
Yishen YeKey Laboratory of Special Engineering Equipment Design and Intelligent Driving Technology, Guilin University of Aerospace Technology, Guilin, 541004, China.
Shifeng HuangKey Laboratory of Special Engineering Equipment Design and Intelligent Driving Technology, Guilin University of Aerospace Technology, Guilin, 541004, China.
Xingguo HanKey Laboratory of Special Engineering Equipment Design and Intelligent Driving Technology, Guilin University of Aerospace Technology, Guilin, 541004, China.
Zhouping HuangKey Laboratory of Special Engineering Equipment Design and Intelligent Driving Technology, Guilin University of Aerospace Technology, Guilin, 541004, China.
Wenfang GuanKey Laboratory of Special Engineering Equipment Design and Intelligent Driving Technology, Guilin University of Aerospace Technology, Guilin, 541004, China.
Zhengwei YangKey Laboratory of Special Engineering Equipment Design and Intelligent Driving Technology, Guilin University of Aerospace Technology, Guilin, 541004, China.
Minggan WangKey Laboratory of Special Engineering Equipment Design and Intelligent Driving Technology, Guilin University of Aerospace Technology, Guilin, 541004, China.

Funding

Guangxi Science and technology planning project 2023AB01248National Natural Science Foundations of China 52365043Natural Science Foundations of Guangxi province 2023JJA160056Natural Science Foundations of Guangxi province 2023JJA160223Young Teachers' Basic Ability Promotion Project of Guangxi 2020KY21012
6 · The paper itself

Abstract

This paper purposed to prepare poly (lactic acid)/continuous cotton thread (PLA /CCT) filaments by using prepreg method, and investigated the properties of PLA/CCT filament and their 3D printed composites. Firstly, a prepreg device was home-made to immerse CCT with PLA melts. The effects of the dragging speed and tensioning equipment on the quality of PLA/CCT filament was investigated. The functions of the immersion temperature, diameter of CCT and alkali treatment of CCT to the tensile properties of PLA/CCT filament were inspected. The results showed that when the dragging speed was 12 r/min, the diameter of the PLA/CCT filament equaled to the standard 3D printed diameter (1.75 mm). Increasing the CCT diameter from 0.6 to 1.0 mm, the tensile strength was improved from 44.26 to 52.81 MPa. The alkali treatment reduced the contact angle of PLA dramatically, and further improved the interfacial compatibility between PLA and CCT, and enhanced the tensile properties of filament composites. Secondly, for achieving CCT without any cutting during the 3D printing, an un-cutting off route was planned. Taguchi experiment was used to investigate how the 3D printing processing parameters affect the flexural properties of the 3D printed PLA/CCT composites. Meanwhile, the impact properties of the 3D printed PLA/CCT composites were analyzed. The results showed that the flexural strength and strain of PLA were improved to 135 MPa and 4.39% with 3D parameters (210℃ of nozzle temperature and 6 mm/s of printing speed). The impact strength of PLA was enhanced dramatically by 5.5% times from 2.75 to 18.87 J/mm

Indexed as

3D printingContinuous cotton threadImpact resistancePLATensile properties

Identifiers

PMID39730705
PMCPMC11681035

What OpenQuestion holds

Textmetadata
LicenceCC BY-NC-ND
Read underepoch 390

Registered trials

None linked

Read under generation 80e0d062 · epoch 390. Bibliography from PubMed, PubMed Central and OpenAlex; grants from NIH RePORTER; trial links from ClinicalTrials.gov; estimates, votes and beliefs from the OpenQuestion graph.