Evidence map›Paper›PMID 39597302›Full record

ArticleMaterials (Basel, Switzerland)2024

Dynamic Analysis and Vibration Control of Additively Manufactured Thin-Walled Polylactic Acid Polymer (PLAP) and PLAP Composite Beam Structures: Numerical Investigation and Experimental Validation.

Ali Raza, Magdalena Mieloszyk, Rūta Rimašauskienė, Vytautas Jūrėnas

Abstract read
In one paragraph

Article in Materials (Basel, Switzerland), 2024. The graph could read no effect estimate from its abstract, so it casts no vote on the map. Cited by 1 paper.

0numbers the graph read from it
0cells of the map it votes in
1citing papers in PubMed
–field-weighted citation impact
1 · What the graph read from it

What it found

Each row is one number read from the abstract, on the scale the paper reported it, with its interval. Left of the dashed line favours the treatment, right favours the comparator. Under each row is the sentence it came from. New to these charts? A ten-minute tutorial.

The abstract states no effect estimate the extractor could read, or names no intervention and outcome on the map, so this paper lights no cell and moves no belief. It is still indexed, cited and linked below.

2 · The registry

The trial behind it

Trials whose registry record cites this paper, or whose number appears in the abstract. A trial that started after this paper was published is citing it as background, not reporting it.

Neither the registry nor the abstract names a trial number. If this is a trial report, that itself is worth knowing.

3 · Its place in the literature

Who cites it

1 citing paper in PubMed.

  1. Article
4 · The record

Corrections and comments

PubMed lists nothing against this paper. Absence here is not a guarantee, only a check that was made.

5 · Who and what money

Authors and funding

4 authors.

Ali RazaFaculty of Mechanical Engineering and Design, Kaunas University of Technology, Studentų Str. 56, LT-51424 Kaunas, Lithuania.
Magdalena MieloszykInstitute of Fluid-Flow Machinery, Polish Academy of Sciences, Fiszera 14 Str., 80-231 Gdansk, Poland.ORCID 0000-0001-7661-2992
Rūta RimašauskienėFaculty of Mechanical Engineering and Design, Kaunas University of Technology, Studentų Str. 56, LT-51424 Kaunas, Lithuania.
Vytautas JūrėnasInstitute of Mechatronics, Kaunas University of Technology, Studentų Str. 56, LT-51424 Kaunas, Lithuania.

Funding

No grant is acknowledged in the PubMed record.

6 · The paper itself

Abstract

This study primarily presents a numerical investigation of the dynamic behavior and vibration control in thin-walled, additively manufactured (AM) beam structures, validated through experimental results. Vibration control in thin-walled structures has gained significant attention recently because vibrations can severely affect structural integrity. Therefore, it is necessary to minimize these vibrations or keep them within acceptable limits to ensure the structure's integrity. In this study, the AM beam structures were made of polylactic acid polymer (PLAP), short carbon fiber reinforced in PLAP (SCFR|PLAP), and continuous carbon fiber reinforced in PLAP (CCFR|PLAP), with 0°|0° layer orientations. The finite element modeling (FEM) of the AM beam structures integrated with macro fiber composite (MFC) was carried out in Abaqus. The initial four modal frequencies of bending modes (BMs) and their respective modal shapes were acquired through numerical simulation. It is crucial to highlight the numerical findings that reveal discrepancies in the 1st modal frequencies of the beams, ranging up to 1.5% compared to their respective experimental values. For the 2nd, 3rd, and 4th modal frequencies, the discrepancies are within 10%. Subsequently, frequency response analysis (FRA) was carried out to observe the frequency-dependent vibration amplitude spectrum at the initial four BM frequencies. Despite discrepancy in the amplitude values between the numerical and experimental datasets, there was consistency in the overall amplitude behavior as frequency varied. THz spectroscopy was performed to identify voids or misalignment errors in the actual beam models. Finally, vibration amplitude control using MFC (M8507-P2) was examined in each kinematically excited numerical beam structure. After applying a counterforce with the MFC, the controlled vibration amplitudes for the PLAP, SCFR|PLAP, and CCFR|PLAP configurations were approximately ±19 µm, ±16 µm, and ±13 µm, respectively. The trend in the controlled amplitudes observed in the numerical findings was consistent with the experimental results. The numerical findings of the study reveal valuable insights for estimating trends related to vibration control in AM beam structures.

Indexed as

amplitude spectrumMFCmodal frequenciesthin-walled beamTHz spectroscopyvibration control

Identifiers

PMID39597302
PMCPMC11595712

What OpenQuestion holds

Textmetadata
LicenceCC BY
Read underepoch 390

Registered trials

None linked

Read under generation 80e0d062 · epoch 390. Bibliography from PubMed, PubMed Central and OpenAlex; grants from NIH RePORTER; trial links from ClinicalTrials.gov; estimates, votes and beliefs from the OpenQuestion graph.