ArticleMaterials (Basel, Switzerland)2024
Intercomparison of Indexable Cutting Inserts' Wear Progress and Chip Formation During Machining Hardened Steel AISI 4337 and Austenitic Stainless Steel AISI 316 L.
Karel Šramhauser, Pavel Kraus, František Špalek, Pavel Černý, Jean de Dieu Marcel Ufitikirezi, Tomáš Zoubek, Miroslav Strob, Yevhen Kononets, Pavel Kříž, Vladimír Vochozka
Abstract read
In one paragraphArticle in Materials (Basel, Switzerland), 2024. The graph could read no effect estimate from its abstract, so it casts no vote on the map. Not yet cited in PubMed.
0numbers the graph read from it
0cells of the map it votes in
0citing papers in PubMed
–field-weighted citation impact
What it found
Each row is one number read from the abstract, on the scale the paper reported it, with its interval. Left of the dashed line favours the treatment, right favours the comparator. Under each row is the sentence it came from. New to these charts? A ten-minute tutorial.
The abstract states no effect estimate the extractor could read, or names no intervention and outcome on the map, so this paper lights no cell and moves no belief. It is still indexed, cited and linked below.
2 · The registryThe trial behind it
Trials whose registry record cites this paper, or whose number appears in the abstract. A trial that started after this paper was published is citing it as background, not reporting it.
Neither the registry nor the abstract names a trial number. If this is a trial report, that itself is worth knowing.
3 · Its place in the literatureWho cites it
0 citing papers in PubMed.
No citing paper in PubMed yet.
4 · The recordCorrections and comments
PubMed lists nothing against this paper. Absence here is not a guarantee, only a check that was made.
5 · Who and what moneyAuthors and funding
10 authors.
Karel ŠramhauserDepartment of Technology and Cybernetics, Faculty of Agriculture and Technology, University of South Bohemia in České Budějovice, 370 05 České Budějovice, Czech Republic.
Pavel KrausInstitute of Technology and Materials, Faculty of Mechanical Engineering, Jan Evangelista Purkyně University in Ústí nad Labem, 400 96 Ústí nad Labem, Czech Republic.
František ŠpalekDepartment of Technology and Cybernetics, Faculty of Agriculture and Technology, University of South Bohemia in České Budějovice, 370 05 České Budějovice, Czech Republic.
Pavel ČernýDepartment of Technology and Cybernetics, Faculty of Agriculture and Technology, University of South Bohemia in České Budějovice, 370 05 České Budějovice, Czech Republic.ORCID 0000-0002-1348-9162 Jean de Dieu Marcel UfitikireziDepartment of Technology and Cybernetics, Faculty of Agriculture and Technology, University of South Bohemia in České Budějovice, 370 05 České Budějovice, Czech Republic.ORCID 0000-0002-2937-9769 Tomáš ZoubekDepartment of Technology and Cybernetics, Faculty of Agriculture and Technology, University of South Bohemia in České Budějovice, 370 05 České Budějovice, Czech Republic.ORCID 0000-0001-8432-1095 Miroslav StrobDepartment of Technology and Cybernetics, Faculty of Agriculture and Technology, University of South Bohemia in České Budějovice, 370 05 České Budějovice, Czech Republic.ORCID 0000-0002-8715-391X Yevhen KononetsDepartment of Technology and Cybernetics, Faculty of Agriculture and Technology, University of South Bohemia in České Budějovice, 370 05 České Budějovice, Czech Republic.ORCID 0000-0002-2095-4640 Pavel KřížDepartment of Technology and Cybernetics, Faculty of Agriculture and Technology, University of South Bohemia in České Budějovice, 370 05 České Budějovice, Czech Republic.ORCID 0000-0002-0328-2117 Vladimír VochozkaDepartment of Applied Physics and Technology, Faculty of Education, University of South Bohemia in České Budějovice, 371 15 České Budějovice, Czech Republic.ORCID 0000-0002-8974-6161 Funding
the OP VVV Project Development of new nano and micro coatings on the surface of selected me-tallic materials-NANOTECH ITI II CZ.02.1.01/0.0/0.0/18_069/0010045
6 · The paper itselfAbstract
This article deals with a mutual comparison of indexable cutting inserts of the CNMG 120408 type from two different manufacturers during the machining of hardened steel AISI 4337 and austenitic stainless steel AISI 316 L. The main goal is to analyse the different wear processes depending on the difference in the manufacturer's design and also depending on the properties of the different machined materials. The progress of the wear of the main spine of the tool, the types of wear and the service life of the cutting edge were monitored, with the achievement of the critical value VB
Indexed as
chip productionhardened steelindexable cutting insertstainless steelwear
Identifiers
PMID39597241
PMCPMC11595980
What OpenQuestion holds
Textmetadata
LicenceCC BY
Read underepoch 390