Microstructure and Hardness Properties of Additively Manufactured AISI 316L Welded by Tungsten Inert Gas and Laser Welding Techniques.

Mohamed Elsayed, Mahmoud Khedr, Antti Järvenpää, A M Gaafer, Atef Hamada

Abstract read

In one paragraph

Article in Materials (Basel, Switzerland), 2024. The graph could read no effect estimate from its abstract, so it casts no vote on the map. Not yet cited in PubMed.

0numbers the graph read from it

0cells of the map it votes in

0citing papers in PubMed

–field-weighted citation impact

1 · What the graph read from it

What it found

Each row is one number read from the abstract, on the scale the paper reported it, with its interval. Left of the dashed line favours the treatment, right favours the comparator. Under each row is the sentence it came from. New to these charts? A ten-minute tutorial.

The abstract states no effect estimate the extractor could read, or names no intervention and outcome on the map, so this paper lights no cell and moves no belief. It is still indexed, cited and linked below.

2 · The registry

The trial behind it

Trials whose registry record cites this paper, or whose number appears in the abstract. A trial that started after this paper was published is citing it as background, not reporting it.

Neither the registry nor the abstract names a trial number. If this is a trial report, that itself is worth knowing.

3 · Its place in the literature

Who cites it

0 citing papers in PubMed.

No citing paper in PubMed yet.

4 · The record

Corrections and comments

PubMed lists nothing against this paper. Absence here is not a guarantee, only a check that was made.

5 · Who and what money

Authors and funding

5 authors.

Mohamed ElsayedMechanical Engineering Department, Faculty of Engineering at Shoubra, Benha University, Cairo 11629, Egypt.ORCID 0000-0002-5928-8470

Mahmoud KhedrMechanical Engineering Department, Faculty of Engineering at Shoubra, Benha University, Cairo 11629, Egypt.ORCID 0000-0002-6418-430X

Antti JärvenpääFuture Manufacturing Technologies (FMT), Kerttu Saalasti Institute, University of Oulu, Pajatie 5, FI-85500 Nivala, Finland.ORCID 0000-0002-4309-4786

A M GaaferMechanical Engineering Department, Faculty of Engineering at Shoubra, Benha University, Cairo 11629, Egypt.

Atef HamadaFuture Manufacturing Technologies (FMT), Kerttu Saalasti Institute, University of Oulu, Pajatie 5, FI-85500 Nivala, Finland.

Funding

Business Finland 4795/31/2021

6 · The paper itself

Abstract

In this study, 316L austenitic stainless-steel (ASS) plates fabricated using an additive manufacturing (AM) process were joined using tungsten inert gas (TIG) and laser welding techniques. The 316L ASS plates were manufactured using a laser powder bed fusion (LPBF) technique, with building orientations (BOs) of 0° and 90°, designated as BO-0 and BO-90, respectively. The study examined the relationship between indentation resistance and microstructure evolution within the fusion zone (FZ) of the welded joints considering the effects of different BOs. Microstructural analysis of the weldments was conducted using optical and laser confocal scanning microscopes, while hardness measurements were obtained using a micro-indentation hardness (H

Indexed as

316L stainless steelhardnesslaser powder bed fusionlaser weldingmicrostructureTIG welding

Identifiers

PMID39336229

DOI10.3390/ma17184489

PMCPMC11433572

What OpenQuestion holds

Textmetadata

LicenceCC BY

Read underepoch 390

Registered trials

None linked

Read under generation 80e0d062 · epoch 390. Bibliography from PubMed, PubMed Central and OpenAlex; grants from NIH RePORTER; trial links from ClinicalTrials.gov; estimates, votes and beliefs from the OpenQuestion graph.