Optimization Milling Force and Surface Roughness of Ti-6Al-4V Based on Ultrasonic-Assisted Milling (UAM): An Experimental Study.

Qingqing Lü, Saiyu Yang, Liquan Yang, Erbo Liu, Guangxi Li, Daohui Xiang

Abstract read

In one paragraph

Article in Micromachines, 2023. The graph could read no effect estimate from its abstract, so it casts no vote on the map. Cited by 1 paper.

0numbers the graph read from it

0cells of the map it votes in

1citing papers in PubMed

–field-weighted citation impact

1 · What the graph read from it

What it found

Each row is one number read from the abstract, on the scale the paper reported it, with its interval. Left of the dashed line favours the treatment, right favours the comparator. Under each row is the sentence it came from. New to these charts? A ten-minute tutorial.

The abstract states no effect estimate the extractor could read, or names no intervention and outcome on the map, so this paper lights no cell and moves no belief. It is still indexed, cited and linked below.

2 · The registry

The trial behind it

Trials whose registry record cites this paper, or whose number appears in the abstract. A trial that started after this paper was published is citing it as background, not reporting it.

Neither the registry nor the abstract names a trial number. If this is a trial report, that itself is worth knowing.

3 · Its place in the literature

Who cites it

1 citing paper in PubMed.

Experimental Investigation on Cutting Characteristics and Surface Quality of TC18 Titanium Alloy in Longitudinal Ultrasonic-Vibration-Assisted Milling Under Dry Conditions.Micromachines · 2026
Article

4 · The record

Corrections and comments

PubMed lists nothing against this paper. Absence here is not a guarantee, only a check that was made.

5 · Who and what money

Authors and funding

6 authors.

Qingqing LüSchool of Mechanical and Power Engineering, Henan Polytechnic University, Jiaozuo 454003, China.

Saiyu YangHenan Province Engineering Research Center of Ultrasonic Technology Application, Pingdingshan University, Pingdingshan 467033, China.

Liquan YangHenan Province Engineering Research Center of Ultrasonic Technology Application, Pingdingshan University, Pingdingshan 467033, China.

Erbo LiuHenan Province Engineering Research Center of Ultrasonic Technology Application, Pingdingshan University, Pingdingshan 467033, China.

Guangxi LiSchool of Mechanical and Power Engineering, Henan Polytechnic University, Jiaozuo 454003, China.

Daohui XiangSchool of Mechanical and Power Engineering, Henan Polytechnic University, Jiaozuo 454003, China.

Funding

Key Scientific Research Fund of Pingdingshan University grant No. PXY-JXZDXK-202306, PXY-BSQD-2019002, PXY-PYJJ-202004This research was funded by Key R & D and Promotion Special/Tackling Key Problems in Science and Technology in Henan province grant No. 212102210349

6 · The paper itself

Abstract

This study aimed to develop a longitudinal ultrasonic-assisted milling system to investigate the machinability of titanium (Ti) Alloy Ti-6Al-4V (TC4). Aiming at reduced milling force and enhanced surface quality, ultrasonic-assisted milling was investigated taking into account the following processing parameters: spindle speed (cutting rate)

Indexed as

micro-texturemilling forceroughnesssurface morphologyultrasonic-assisted milling

Identifiers

PMID37763862

DOI10.3390/mi14091699

PMCPMC10537650

What OpenQuestion holds

Textmetadata

LicenceCC BY

Read underepoch 390

Registered trials

None linked

Read under generation 80e0d062 · epoch 390. Bibliography from PubMed, PubMed Central and OpenAlex; grants from NIH RePORTER; trial links from ClinicalTrials.gov; estimates, votes and beliefs from the OpenQuestion graph.