Characteristics of Elliptical Vibration-Assisted Cutting with Variations in Tilt Angle of Elliptical Locus.

Senbin Xia, Ziqiang Yin, Cheng Huang, Yawen Guo, Chao Zhang

Open access · goldAbstract read

In one paragraph

Article in Micromachines, 2023. The graph could read no effect estimate from its abstract, so it casts no vote on the map. Cited by 1 paper.

0numbers the graph read from it

0cells of the map it votes in

1citing papers in PubMed

0.1field-weighted citation impact, top 60% of its field

1 · What the graph read from it

What it found

Each row is one number read from the abstract, on the scale the paper reported it, with its interval. Left of the dashed line favours the treatment, right favours the comparator. Under each row is the sentence it came from. New to these charts? A ten-minute tutorial.

The abstract states no effect estimate the extractor could read, or names no intervention and outcome on the map, so this paper lights no cell and moves no belief. It is still indexed, cited and linked below.

2 · The registry

The trial behind it

Trials whose registry record cites this paper, or whose number appears in the abstract. A trial that started after this paper was published is citing it as background, not reporting it.

Neither the registry nor the abstract names a trial number. If this is a trial report, that itself is worth knowing.

3 · Its place in the literature

Who cites it

1 citing paper in PubMed, 1 citations in OpenAlex.

Atomic-Scale Mechanisms of Ultrasonic-Assisted Ultra-Precision Cutting of W-Mo70 Alloy: Experimental Benchmarking and Molecular Dynamics Simulation.Micromachines · 2026
Article

4 · The record

Corrections and comments

PubMed lists nothing against this paper. Absence here is not a guarantee, only a check that was made.

5 · Who and what money

Authors and funding

5 authors at 1 institution in 1 country.

Senbin XiaState Key Laboratory of Precision Electronic Manufacturing Technology and Equipment, Guangdong University of Technology, Guangzhou 510006, China.

Ziqiang YinState Key Laboratory of Precision Electronic Manufacturing Technology and Equipment, Guangdong University of Technology, Guangzhou 510006, China.

Cheng HuangState Key Laboratory of Precision Electronic Manufacturing Technology and Equipment, Guangdong University of Technology, Guangzhou 510006, China.

Yawen GuoState Key Laboratory of Precision Electronic Manufacturing Technology and Equipment, Guangdong University of Technology, Guangzhou 510006, China.

Chao ZhangSchool of Electromechanical Engineering, Guangdong University of Technology, Guangzhou 510006, China.

Guangdong University of Technology · CN

Funding

Science and Technology Innovation Program of Hunan Province 2022RC4014Science and Technology Program of Guangzhou 201804020040

6 · The paper itself

Abstract

Elliptical vibration-assisted cutting (EVAC), one of the advanced micromachining methods, enables results not possible with traditional ultra-precision machining. It is considered to be one of the most viable options for manufacturing micro/nanostructured surfaces. However, it is difficult to control the elliptical locus with different tilt angles; therefore, previous studies have primarily focused on fixed locus and investigated the effects of the amplitude and frequency on machining performance. In addition, tilt angle is an important factor affecting the characteristics of EVAC. To maximize the cutting performance of EVAC, the cutting characteristics of EVAC with variations in tilt angle of elliptical locus are investigated. The mathematical model of elliptical trajectory based on different tilt angles is established via geometric analysis. The effects of the different tilt angle (0-180°) on cutting forces, chip formation, defect generation and surface roughness are observed and theoretically analyzed in microgroove experiments. The experimental results show that the tilt angle has a significant effect on the cutting force, chip formation, defects and surface roughness. The best cutting performance can be obtained at the tilt angle of 30°, while the worst is recorded at 90°. The results can provide a valuable reference for further comprehensive studies to maximize the cutting performance of EVAC.

Indexed as

diamond cuttingelliptical locuselliptical vibration-assisted cuttingtilt angle

Identifiers

PMID37512737

DOI10.3390/mi14071426

PMCPMC10385585

OpenAlexW4384557667

What OpenQuestion holds

Textmetadata

LicenceCC BY

Read underepoch 390

Registered trials

None linked

Read under generation 80e0d062 · epoch 390. Bibliography from PubMed, PubMed Central and OpenAlex; grants from NIH RePORTER; trial links from ClinicalTrials.gov; estimates, votes and beliefs from the OpenQuestion graph.