ArticleMaterials (Basel, Switzerland)2023
Analysis of the Mechanical Properties of 3D-Printed Plastic Samples Subjected to Selected Degradation Effects.
Article in Materials (Basel, Switzerland), 2023. The graph could read no effect estimate from its abstract, so it casts no vote on the map. Cited by 21 papers.
What it found
Each row is one number read from the abstract, on the scale the paper reported it, with its interval. Left of the dashed line favours the treatment, right favours the comparator. Under each row is the sentence it came from. New to these charts? A ten-minute tutorial.
The abstract states no effect estimate the extractor could read, or names no intervention and outcome on the map, so this paper lights no cell and moves no belief. It is still indexed, cited and linked below.
The trial behind it
Trials whose registry record cites this paper, or whose number appears in the abstract. A trial that started after this paper was published is citing it as background, not reporting it.
Neither the registry nor the abstract names a trial number. If this is a trial report, that itself is worth knowing.
Who cites it
21 citing papers in PubMed.
- Article
- Engineering integrated evaporation solutions: Harmonizing manual approaches with automated laboratory workflows.SLAS technology · 2026Article
- Testing of milling cutter with the conformal cooling channels produced by the selective laser melting technology.Scientific reports · 2026Article
- Three-dimensional bioprinted hydrogels for the management of diabetic wounds: A review.BioImpacts : BI · 2026Review
- Enhancing the Performance of FFF-Printed Parts: A Review of Reinforcement and Modification Strategies for Thermoplastic Polymers.Materials (Basel, Switzerland) · 2025Review
- Prediction of Fracture Loads in 3D-Printed ASA and Carbon-Fiber Reinforced ASA Notched Specimens Using the Calibrated ASED Criterion.Materials (Basel, Switzerland) · 2025Article
- Comparative analysis of machinability and microstructure in LPBF and conventionally processed M300 maraging steel.Scientific reports · 2025Article
- A Proposed System for Temperature Measurement During Tensile Testing.Sensors (Basel, Switzerland) · 2025Article
- Optimizing Interfacial Adhesion and Mechanical Performance of Multimaterial Joints Fabricated by Material Extrusion.Materials (Basel, Switzerland) · 2025Article
- Investigation of Color and Mechanical Properties of Parts Printed on 3D Printers After Salt Spray Testing.Polymers · 2025Article
- Assessment of the Drone Arm's Plastic-Metal Joint Mechanical Resistance Following Natural and Artificial Aging of the 3D-Printed Plastic Component.Materials (Basel, Switzerland) · 2025Article
- Effect of Accelerated Degradation on the Dimensions and Mechanical Performance of 3D-Printed PLA Parts Using Different Filament Manufacturing Techniques.Materials (Basel, Switzerland) · 2025Article
- Investigation of Mechanical Properties and Color Changes of 3D-Printed Parts with Different Infill Ratios and Colors After Aging.Materials (Basel, Switzerland) · 2024Article
- Article
- A Sensor Probe with Active and Passive Humidity Management for In Situ Soil COSensors (Basel, Switzerland) · 2024Article
- Examining the Flexural Behavior of Thermoformed 3D-Printed Wrist-Hand Orthoses: Role of Material, Infill Density, and Wear Conditions.Polymers · 2024Article
- Effect of Degradation of Polylactic Acid (PLA) on Dynamic Mechanical Response of 3D Printed Lattice Structures.Materials (Basel, Switzerland) · 2024Article
- Change in the Low-Cycle Performance on the 3D-Printed Materials ABS, ASA, HIPS, and PLA Exposed to Mineral Oil.Polymers · 2024Article
- Effect of Shock-Variable Environmental Temperature and Humidity Conditions on 3D-Printed Polymers for Tensile Properties.Polymers · 2023Article
- Mechanical Performance of 3D-Printed Polyethylene Fibers and Their Durability against Degradation.Materials (Basel, Switzerland) · 2023Article
Corrections and comments
PubMed lists nothing against this paper. Absence here is not a guarantee, only a check that was made.
Authors and funding
8 authors.
Funding
Abstract
The Fused Filament Fabrication (FFF) method is an additive technology that is used for the creation of prototypes within Rapid Prototyping (RP) as well as for the creation of final components in piece or small-series production. The possibility of using FFF technology in the creation of final products requires knowledge of the properties of the material and, at the same time, how these properties change due to degradation effects. In this study, the mechanical properties of the selected materials (PLA, PETG, ABS, and ASA) were tested in their non-degenerate state and after exposure of the samples to the selected degradation factors. For the analysis, which was carried out by the tensile test and the Shore D hardness test, samples of normalized shape were prepared. The effects of UV radiation, high temperature environments, high humidity environments, temperature cycles, and exposure to weather conditions were monitored. The parameters obtained from the tests (tensile strength and Shore D hardness) were statistically evaluated, and the influence of degradation factors on the properties of individual materials was assessed. The results showed that even between individual manufacturers of the same filament there are differences, both in the mechanical properties and in the behavior of the material after exposure to degradation effects.
Indexed as
Identifiers
What OpenQuestion holds
Registered trials
Read under generation 80e0d062 · epoch 390. Bibliography from PubMed, PubMed Central and OpenAlex; grants from NIH RePORTER; trial links from ClinicalTrials.gov; estimates, votes and beliefs from the OpenQuestion graph.