Modelling of the Face-Milling Process by Toroidal Cutter.

Marcin Płodzień, Łukasz Żyłka, Antun Stoić

Abstract read

In one paragraph

Article in Materials (Basel, Switzerland), 2023. The graph could read no effect estimate from its abstract, so it casts no vote on the map. Cited by 1 paper.

0numbers the graph read from it

0cells of the map it votes in

1citing papers in PubMed

–field-weighted citation impact

1 · What the graph read from it

What it found

Each row is one number read from the abstract, on the scale the paper reported it, with its interval. Left of the dashed line favours the treatment, right favours the comparator. Under each row is the sentence it came from. New to these charts? A ten-minute tutorial.

The abstract states no effect estimate the extractor could read, or names no intervention and outcome on the map, so this paper lights no cell and moves no belief. It is still indexed, cited and linked below.

2 · The registry

The trial behind it

Trials whose registry record cites this paper, or whose number appears in the abstract. A trial that started after this paper was published is citing it as background, not reporting it.

Neither the registry nor the abstract names a trial number. If this is a trial report, that itself is worth knowing.

3 · Its place in the literature

Who cites it

1 citing paper in PubMed.

The Review of Current and Proposed Methods of Manufacturing Fir Tree Slots of Turbine Aero Engine Discs.Materials (Basel, Switzerland) · 2023
Review

4 · The record

Corrections and comments

PubMed lists nothing against this paper. Absence here is not a guarantee, only a check that was made.

5 · Who and what money

Authors and funding

3 authors.

Marcin PłodzieńDepartment of Manufacturing Techniques and Automation, The Faculty of Mechanical Engineering and Aeronautics, Rzeszow University of Technology, ul. W. Pola 2, 35-959 Rzeszow, Poland.

Łukasz ŻyłkaDepartment of Manufacturing Techniques and Automation, The Faculty of Mechanical Engineering and Aeronautics, Rzeszow University of Technology, ul. W. Pola 2, 35-959 Rzeszow, Poland.ORCID 0000-0003-0136-1548

Antun StoićMechanical Engineering Faculty, University of Slavonski Brod, Trg Ivane Brlic Mazuranic 2, 35000 Slavonski Brod, Croatia.

Funding

No grant is acknowledged in the PubMed record.

6 · The paper itself

Abstract

When face milling using a toroidal cutter, with a change in the depth of the cut, the entering angle varies as well. An experimental test of the influence of cutting parameters, such as the depth of the cut and the feed per tooth on the cutting force components and surface roughness parameters, was conducted. The experimental test was carried out using a DMU 100 monoBLOCK CNC machine with registration of cutting force components and surface roughness parameters Ra, Rz, and RSm. FEM analysis of the face-milling process was also carried out and compared with the experimental results. The average deviation of the FEM values for cutting force components does not exceed 12%. Experimental models were established for each force component. It was shown that the depth of the cut has the strongest influence on each force component. The feed per tooth has a little impact on the cutting force. The obtained model of the feed force component is the most complex, and the model of the F

Indexed as

cutting forceforce modelroughness modelsurface roughnesstoroidal cutter

Identifiers

PMID37049123

DOI10.3390/ma16072829

PMCPMC10096468

What OpenQuestion holds

Textmetadata

LicenceCC BY

Read underepoch 390

Registered trials

None linked

Read under generation 80e0d062 · epoch 390. Bibliography from PubMed, PubMed Central and OpenAlex; grants from NIH RePORTER; trial links from ClinicalTrials.gov; estimates, votes and beliefs from the OpenQuestion graph.