ArticleMaterials (Basel, Switzerland)2022
The Influence of the Structure Parameters on the Mechanical Properties of Cylindrically Mapped Gyroid TPMS Fabricated by Selective Laser Melting with 316L Stainless Steel Powder.
Article in Materials (Basel, Switzerland), 2022. The graph could read no effect estimate from its abstract, so it casts no vote on the map. Cited by 14 papers.
What it found
Each row is one number read from the abstract, on the scale the paper reported it, with its interval. Left of the dashed line favours the treatment, right favours the comparator. Under each row is the sentence it came from. New to these charts? A ten-minute tutorial.
The abstract states no effect estimate the extractor could read, or names no intervention and outcome on the map, so this paper lights no cell and moves no belief. It is still indexed, cited and linked below.
The trial behind it
Trials whose registry record cites this paper, or whose number appears in the abstract. A trial that started after this paper was published is citing it as background, not reporting it.
Neither the registry nor the abstract names a trial number. If this is a trial report, that itself is worth knowing.
Who cites it
14 citing papers in PubMed.
- Mechanistic Elucidation of Dynamic Deformation Transitions and Energy Absorption in Gyroid Structures Across Relative Densities and Compression Velocities.Materials (Basel, Switzerland) · 2026Article
- An Overview of Additive Manufacturing of Triply Periodic Minimal Surface (TPMS) Structures.Polymers · 2025Review
- AWJ Cutting Process Quality Modeling and Optimization Based on Footprint Angle.Materials (Basel, Switzerland) · 2025Article
- Assessment of the Feasibility of Using Additive Manufacturing from Metal Powder to Produce Compact Heat Exchangers.Materials (Basel, Switzerland) · 2025Article
- Bending Performance of Diamond Lattice Cylindrical Shells.Materials (Basel, Switzerland) · 2025Article
- Definition, Fabrication, and Compression Testing of Sandwich Structures with Novel TPMS-Based Cores.Materials (Basel, Switzerland) · 2024Article
- Mechanical Behaviour of Photopolymer Cell-Size Graded Triply Periodic Minimal Surface Structures at Different Deformation Rates.Materials (Basel, Switzerland) · 2024Article
- Identification of Hybrid Polymer Material STERED and Basic Material Properties Used in Road Substructures or Pavements.Polymers · 2024Article
- The Influence of Heat Treatment Temperature on Tensile Properties of Metal-Bonded Diamond Composites Fabricated via Selective Laser Melting.Materials (Basel, Switzerland) · 2023Article
- Mechanical Properties and Energy Absorption Abilities of Diamond TPMS Cylindrical Structures Fabricated by Selective Laser Melting with 316L Stainless Steel.Materials (Basel, Switzerland) · 2023Article
- Preliminary Studies into Cutting of a Novel Two Component 3D-Printed Stainless Steel-Polymer Composite Material by Abrasive Water Jet.Materials (Basel, Switzerland) · 2023Article
- Development of a Three-Dimensional Optical Verification Technology without Environmental Pollution for Metal Components with Different Surface Properties.Materials (Basel, Switzerland) · 2022Article
- An Environmentally-Friendly Three-Dimensional Computer-Aided Verification Technique for Plastic Parts.Polymers · 2022Article
- Topological and Mechanical Properties of Different Lattice Structures Based on Additive Manufacturing.Micromachines · 2022Article
Corrections and comments
PubMed lists nothing against this paper. Absence here is not a guarantee, only a check that was made.
Authors and funding
4 authors.
Funding
No grant is acknowledged in the PubMed record.
Abstract
The development of additive manufacturing techniques has made it possible to produce porous structures with complex geometry with unique properties as potential candidates for energy absorption, heat dissipation, biomedical, and vibration control application. Recently, there has been increased interest in additively manufacturing porous structures based on triply periodic minimal surfaces (TPMS) topology. In this paper, the mechanical properties and energy absorption abilities of cylindrical mapped TPMS structures with shell gyroid unit cells fabricated by selective laser melting (SLM) with 316L stainless steel under compression loading were investigated. Based on the experimental study, it was found that tested structures exhibited two different deformation modes. There is also a relationship between the number and shapes of unit cells in the structure and the elastic modulus, yield strength, plateau stress, and energy absorption. These results can be used to design and manufacture more efficient lightweight parts lattices for energy absorbing applications, e.g., in the field of biomedical and bumpers applications. The deformation mode for each tested sample was also presented on the records obtained from the ARAMIS system.
Indexed as
Identifiers
What OpenQuestion holds
Registered trials
Read under generation 80e0d062 · epoch 390. Bibliography from PubMed, PubMed Central and OpenAlex; grants from NIH RePORTER; trial links from ClinicalTrials.gov; estimates, votes and beliefs from the OpenQuestion graph.