ArticleMaterials (Basel, Switzerland)2022
Influence of the Milling Conditions of Aluminium Alloy 2017A on the Surface Roughness.
Article in Materials (Basel, Switzerland), 2022. The graph could read no effect estimate from its abstract, so it casts no vote on the map. Cited by 6 papers.
What it found
Each row is one number read from the abstract, on the scale the paper reported it, with its interval. Left of the dashed line favours the treatment, right favours the comparator. Under each row is the sentence it came from. New to these charts? A ten-minute tutorial.
The abstract states no effect estimate the extractor could read, or names no intervention and outcome on the map, so this paper lights no cell and moves no belief. It is still indexed, cited and linked below.
The trial behind it
Trials whose registry record cites this paper, or whose number appears in the abstract. A trial that started after this paper was published is citing it as background, not reporting it.
Neither the registry nor the abstract names a trial number. If this is a trial report, that itself is worth knowing.
Who cites it
6 citing papers in PubMed.
- Development of a novel integrated RSM-Fuzzy MCDA framework for high-speed machinability assessment of WAAM-Fabricated aluminium.Scientific reports · 2026Article
- Application of Machine Learning to the Prediction of Surface Roughness in the Milling Process on the Basis of Sensor Signals.Materials (Basel, Switzerland) · 2025Article
- The Influence of Insert Mounting Errors on the Surface Roughness of 1.0503 Steel in Face Milling.Materials (Basel, Switzerland) · 2024Article
- Effect of the Technological Parameters of Milling on Residual Stress in the Surface Layer of Thin-Walled Plates.Materials (Basel, Switzerland) · 2024Article
- Influence of the Relative Displacements and the Minimum Chip Thickness on the Surface Texture in Shoulder Milling.Materials (Basel, Switzerland) · 2023Article
- Analyzing the Potential of Drill Bits 3D Printed Using the Direct Metal Laser Melting (DMLM) Technology to Drill Holes in Polyamide 6 (PA6).Materials (Basel, Switzerland) · 2023Article
Corrections and comments
PubMed lists nothing against this paper. Absence here is not a guarantee, only a check that was made.
Authors and funding
5 authors.
Funding
No grant is acknowledged in the PubMed record.
Abstract
The article presents the results and process analysis of the face milling of aluminium alloy 2017A with the CoroMill 490 tool on an AVIA VMC 800 vertical milling centre. The study analysed the effects of the cutting speed, the feed rate, the actual number of teeth involved in the process, the minimum thickness of the cut layer (hmin), and the relative displacement in the tool-workpiece system D(ξ) on the surface roughness parameter Ra. To measure relative displacement, an original bench was used with an XL-80 laser interferometer. The analysis of relative displacement and surface roughness allowed these factors to be correlated with each other. The purpose of this article is to determine the stable operating ranges of the CoroMill 490-050Q22-08M milling head with respect to the value of the generated relative displacement w during the face-milling process and to determine its influence on surface roughness. The research methodology presented in this paper and the cutting tests carried out allowed the determination of the optimum operating parameters of the CoroMill 490-050Q22-08M tool during the face milling of aluminium alloy 2017A, which are vc 300 m/m and fz—0.14 mm/tooth. Working with the defined cutting parameters allows all the cutting inserts in the tool body to be involved in shaping the geometrical structure of the surface, while maintaining a low vibration level D(ξ) > 1 µm, a low value of the parameter hmin > 1.5 µm, and the desired value of the parameter Ra > 0.2 µm
Indexed as
Identifiers
What OpenQuestion holds
Registered trials
Read under generation 80e0d062 · epoch 390. Bibliography from PubMed, PubMed Central and OpenAlex; grants from NIH RePORTER; trial links from ClinicalTrials.gov; estimates, votes and beliefs from the OpenQuestion graph.