High-Performance of a Thick-Walled Polyamide Composite Produced by Microcellular Injection Molding.

Dariusz Sykutera, Piotr Czyżewski, Piotr Szewczykowski

Open access · goldAbstract read

In one paragraph

Article in Materials (Basel, Switzerland), 2021. The graph could read no effect estimate from its abstract, so it casts no vote on the map. Cited by 1 paper.

0numbers the graph read from it

0cells of the map it votes in

1citing papers in PubMed

0.6field-weighted citation impact, top 41% of its field

1 · What the graph read from it

What it found

Each row is one number read from the abstract, on the scale the paper reported it, with its interval. Left of the dashed line favours the treatment, right favours the comparator. Under each row is the sentence it came from. New to these charts? A ten-minute tutorial.

The abstract states no effect estimate the extractor could read, or names no intervention and outcome on the map, so this paper lights no cell and moves no belief. It is still indexed, cited and linked below.

2 · The registry

The trial behind it

Trials whose registry record cites this paper, or whose number appears in the abstract. A trial that started after this paper was published is citing it as background, not reporting it.

Neither the registry nor the abstract names a trial number. If this is a trial report, that itself is worth knowing.

3 · Its place in the literature

Who cites it

1 citing paper in PubMed, 8 citations in OpenAlex.

Structure Analysis and Its Correlation with Mechanical Properties of Microcellular Polyamide Composites Reinforced with Glass Fibers.Materials (Basel, Switzerland) · 2023
Article

4 · The record

Corrections and comments

PubMed lists nothing against this paper. Absence here is not a guarantee, only a check that was made.

5 · Who and what money

Authors and funding

3 authors at 1 institution in 1 country.

Dariusz SykuteraDepartment of Manufacturing Techniques, Faculty of Mechanical Engineering, UTP University of Science and Technology, Kaliskiego 7, 85-796 Bydgoszcz, Poland.ORCID 0000-0001-8736-5093

Piotr CzyżewskiDepartment of Manufacturing Techniques, Faculty of Mechanical Engineering, UTP University of Science and Technology, Kaliskiego 7, 85-796 Bydgoszcz, Poland.

Piotr SzewczykowskiDepartment of Manufacturing Techniques, Faculty of Mechanical Engineering, UTP University of Science and Technology, Kaliskiego 7, 85-796 Bydgoszcz, Poland.

Bydgoszcz University of Science and Technology · PL

Funding

Ministerstwo Nauki i Szkolnictwa Wyższego Project No. BN-1/2021, Low-emission technologies of manufacturing and mechanical recycling in the circular economy.

6 · The paper itself

Abstract

Lightweight moldings obtained by microcellular injection molding (MIM) are of great significance for saving materials and reducing energy consumption. For thick-walled parts, the standard injection molding process brings some defects, including a sink mark, warpage, and high shrinkage. Polyamide 66 (PA66)/glass fiber (GF) thick-walled moldings were prepared by MuCell

Indexed as

FEM simulationmicrocellular injection moldingmicro CT analysisMuCell® technologyreinforced PA66 GF30 compositethick-walled moldings

Identifiers

PMID34361391

DOI10.3390/ma14154199

PMCPMC8348799

OpenAlexW3185535085

What OpenQuestion holds

Textmetadata

LicenceCC BY

Read underepoch 390

Registered trials

None linked

Read under generation 80e0d062 · epoch 390. Bibliography from PubMed, PubMed Central and OpenAlex; grants from NIH RePORTER; trial links from ClinicalTrials.gov; estimates, votes and beliefs from the OpenQuestion graph.