ArticlePolymers2021
Effect of Printing Parameters on the Thermal and Mechanical Properties of 3D-Printed PLA and PETG, Using Fused Deposition Modeling.
Article in Polymers, 2021. The graph could read no effect estimate from its abstract, so it casts no vote on the map. Cited by 71 papers.
What it found
Each row is one number read from the abstract, on the scale the paper reported it, with its interval. Left of the dashed line favours the treatment, right favours the comparator. Under each row is the sentence it came from. New to these charts? A ten-minute tutorial.
The abstract states no effect estimate the extractor could read, or names no intervention and outcome on the map, so this paper lights no cell and moves no belief. It is still indexed, cited and linked below.
The trial behind it
Trials whose registry record cites this paper, or whose number appears in the abstract. A trial that started after this paper was published is citing it as background, not reporting it.
Neither the registry nor the abstract names a trial number. If this is a trial report, that itself is worth knowing.
Who cites it
71 citing papers in PubMed, 299 citations in OpenAlex.
- Article
- 3D-Printed PLA/HA Composite Scaffolds: Balancing Mechanical Properties for Bone Tissue Engineering.Materials (Basel, Switzerland) · 2026Article
- The Influence of Certain Operating Conditions of the FDM Process on the Mechanical Properties of Polymeric Materials-A Review.Polymers · 2026Review
- Mechanical Performance of FDM-Printed PLA Joined by Portable Friction Stir Welding: Influence of Infill Density and Tool Pin Geometry.Polymers · 2026Article
- Article
- Mechanical and Microstructural Response of FDM-Printed PETG and PETG+CF to Variable Infill Architecture and Lubricant Exposure.Polymers · 2026Article
- Low-cost oscillating sieving shaker machine for granulometry analysis in food science.HardwareX · 2026Article
- Fabrication Process and Particle Dispersion Characteristics of W-PETG-Based 3D-Printed Composites for Medical Radiation Shielding.Polymers · 2026Article
- Biomimetic Assessment of 3D-Printed T-Shape Joints Bio-Inspired by the Stem-Branch Junction in Common Ash (Biomimetics (Basel, Switzerland) · 2025Article
- Optimization of Roughness, Dimensional Conformity, and Porosity of 3D-Printed ASA with MEX: Impact of Critical Process Control Parameters.ACS omega · 2025Article
- Influence of Layer Thickness and Extrusion Temperature on the Mechanical Behavior of PLA-Flax TPMS Sandwich Structures Fabricated via Fused Filament Fabrication.Materials (Basel, Switzerland) · 2025Article
- Enhancing the Performance of FFF-Printed Parts: A Review of Reinforcement and Modification Strategies for Thermoplastic Polymers.Materials (Basel, Switzerland) · 2025Review
- Taguchi-Based Optimization of FDM Parameters for Sub-150 µm Microchannels: Comparative Study of PETG and TPU.Micromachines · 2025Article
- Optimizing Interfacial Adhesion and Mechanical Performance of Multimaterial Joints Fabricated by Material Extrusion.Materials (Basel, Switzerland) · 2025Article
- Investigation of Buckling and Failure in Thin-Walled Columns Fabricated from PLA and PETG Using FDM 3D Printing.Materials (Basel, Switzerland) · 2025Article
- Article
- Optimization of Produced Parameters for PA6/PA6GF30 Composite Produced by 3D Printing with Novel Knitting Method.Polymers · 2025Article
- Mechanical Characterization of FDM 3D-Printed Components Using Advanced Measurement and Modeling Techniques.Materials (Basel, Switzerland) · 2025Article
- Multi-Objective Optimization of Low-Velocity Impact and Compression Behavior of 3D-Printed PLA Cubic Samples.Polymers · 2025Article
- Machine learning driven optimization of compressive strength of 3D printed bio polymer composite material.PloS one · 2025Article
11 more citing papers are in PubMed but not listed here.
Corrections and comments
PubMed lists nothing against this paper. Absence here is not a guarantee, only a check that was made.
Authors and funding
7 authors at 3 institutions in 1 country.
Funding
Abstract
Fused Deposition Modeling (FDM) can be used to manufacture any complex geometry and internal structures, and it has been widely applied in many industries, such as the biomedical, manufacturing, aerospace, automobile, industrial, and building industries. The purpose of this research is to characterize the polylactic acid (PLA) and polyethylene terephthalate glycol (PETG) materials of FDM under four loading conditions (tension, compression, bending, and thermal deformation), in order to obtain data regarding different printing temperatures and speeds. The results indicated that PLA and PETG materials exhibit an obvious tensile and compression asymmetry. It was observed that the mechanical properties (tension, compression, and bending) of PLA and PETG are increased at higher printing temperatures, and that the effect of speed on PLA and PETG shows different results. In addition, the mechanical properties of PLA are greater than those of PETG, but the thermal deformation is the opposite. The above results will be a great help for researchers who are working with polymers and FDM technology to achieve sustainability.
Indexed as
Identifiers
What OpenQuestion holds
Registered trials
Read under generation 80e0d062 · epoch 390. Bibliography from PubMed, PubMed Central and OpenAlex; grants from NIH RePORTER; trial links from ClinicalTrials.gov; estimates, votes and beliefs from the OpenQuestion graph.