ArticleBioMed research international2019
Influence of Bulk-Fill Composites, Polimerization Modes, and Remaining Dentin Thickness on Intrapulpal Temperature Rise.
Article in BioMed research international, 2019. The graph could read no effect estimate from its abstract, so it casts no vote on the map. Cited by 13 papers.
What it found
Each row is one number read from the abstract, on the scale the paper reported it, with its interval. Left of the dashed line favours the treatment, right favours the comparator. Under each row is the sentence it came from. New to these charts? A ten-minute tutorial.
The abstract states no effect estimate the extractor could read, or names no intervention and outcome on the map, so this paper lights no cell and moves no belief. It is still indexed, cited and linked below.
The trial behind it
Trials whose registry record cites this paper, or whose number appears in the abstract. A trial that started after this paper was published is citing it as background, not reporting it.
Neither the registry nor the abstract names a trial number. If this is a trial report, that itself is worth knowing.
Who cites it
13 citing papers in PubMed, 27 citations in OpenAlex.
- In vitro assessment of the role of air spray on pulp temperature changes for preheated resin composite Class V restorations in lower incisor.Odontology · 2026Article
- Effect of an Air Stream Directed Across the Tooth on the Degree of Conversion and Temperature of Preheated Bulk-Fill Resin-Based Composites.Materials (Basel, Switzerland) · 2026Article
- In vitro changes in pulpal temperature during light exposure at different pulpal fluid flows.Odontology · 2026Article
- Influence of Post System and Geometry on Radiant Energy Transmission Through the Side of Different Prefabricated Fiber Post Systems.Polymers · 2026Article
- Influence of indirect air-cooling on the variation in intrapulpal temperature during rapid high-intensity light-curing using a bulk-fill resin composite.Journal of clinical and experimental dentistry · 2025Article
- Effect of Rapid High-Intensity Light-Curing on Increasing Transdentinal Temperature and Cell Viability: An In Vitro Study.Polymers · 2024Article
- Influence of light exposure techniques on in vitro pulp temperature rise during bulk fill composite Class I restorations.Odontology · 2024Article
- Evaluation of dentinal tubule occlusion and pulp tissue response after using 980-nm diode laser for dentin hypersensitivity treatment.Clinical oral investigations · 2023Article
- In vitro temperature changes in the pulp chamber caused by laser and Quadwave LED-light curing units.Odontology · 2023Article
- Temperature changes and hardness of resin-based composites light-cured with laser diode or light-emitting diode curing lights.Odontology · 2023Article
- In vitro attrition wear resistance of four types of paste-like bulk-fill composite resins.BMC oral health · 2022Article
- Does the heat generated by fluorescence-aided caries excavation system effect the pulp temperature of primary teeth irreversibly? AnJournal of clinical and experimental dentistry · 2021Article
- Heat Development in the Pulp Chamber During Curing Process of Resin-Based Composite Using Multi-Wave LED Light Curing Unit.Clinical, cosmetic and investigational dentistry · 2020Article
Corrections and comments
PubMed lists nothing against this paper. Absence here is not a guarantee, only a check that was made.
Authors and funding
2 authors at 1 institution in 1 country.
Funding
No grant is acknowledged in the PubMed record.
Abstract
objectivesThe aim of this study was to compare the effects of different bulk-fill resin composites, polimerization modes, and the thickness of remaining dentin on the increase of intrapulpal temperature.
methodsHuman-extracted upper premolar teeth (
resultsNo significant statistical differences in intrapulpal temperature rise between low viscosity bulk-fill composites (SDR and Estelite) were found. The lowest intrapulpal temperature rise was found in groups which used the Filtek Bulk-fill composite. Decreases in the remaining dentin thickness increased the intrapulpal temperature rise. SIGNIFICANCE: This study demonstrated that remaining dentin thickness, filler ratio of bulk-fill composites, and power and application time of the LED-LCU may affect intrapulpal temperature rise.
Indexed as
Identifiers
What OpenQuestion holds
Registered trials
Read under generation 80e0d062 · epoch 390. Bibliography from PubMed, PubMed Central and OpenAlex; grants from NIH RePORTER; trial links from ClinicalTrials.gov; estimates, votes and beliefs from the OpenQuestion graph.