ReviewMaterials (Basel, Switzerland)2019
Sustainable Lubrication Methods for the Machining of Titanium Alloys: An Overview.
Review in Materials (Basel, Switzerland), 2019. The graph could read no effect estimate from its abstract, so it casts no vote on the map. Cited by 15 papers.
What it found
Each row is one number read from the abstract, on the scale the paper reported it, with its interval. Left of the dashed line favours the treatment, right favours the comparator. Under each row is the sentence it came from. New to these charts? A ten-minute tutorial.
The abstract states no effect estimate the extractor could read, or names no intervention and outcome on the map, so this paper lights no cell and moves no belief. It is still indexed, cited and linked below.
The trial behind it
Trials whose registry record cites this paper, or whose number appears in the abstract. A trial that started after this paper was published is citing it as background, not reporting it.
Neither the registry nor the abstract names a trial number. If this is a trial report, that itself is worth knowing.
Who cites it
15 citing papers in PubMed.
- Turning Data Optimization of Titanium Alloy Produced by Casting and DMLS.Materials (Basel, Switzerland) · 2025Article
- Alloy Selection and Manufacturing Technologies for Total Ankle Arthroplasty: A Narrative Review.Materials (Basel, Switzerland) · 2025Review
- Tribological performance and lubrication mechanism of polyacrylamide as a high-efficiency water-based lubricant additive for titanium alloys.Scientific reports · 2025Article
- Optimizing Cutting Parameters for Enhanced Control of Temperature, Cutting Forces, and Energy Consumption in Dry Turning of Ti6Al4V Alloy.Materials (Basel, Switzerland) · 2025Article
- Advanced Optimization of Surface Characteristics and Material Removal Rate for Biocompatible Ti6Al4V Using WEDM Process with BBD and NSGA II.Materials (Basel, Switzerland) · 2023Article
- The Effects of Lubricooling Ecosustainable Techniques on Tool Wear in Carbon Steel Milling.Materials (Basel, Switzerland) · 2023Article
- Optimization of the Dry Turning Process of Ti48Al2Cr2Nb Aluminide Based on the Cutting Tool Configuration.Materials (Basel, Switzerland) · 2022Article
- Experimental investigations into the performance of die-sinking mixed-gas atomization discharge ablation process on titanium alloy.Scientific reports · 2022Article
- Corrosion Resistance and Surface Bioactivity of Ti6Al4V Alloy after Finish Turning under Ecological Cutting Conditions.Materials (Basel, Switzerland) · 2021Article
- Surface Integrity and Tool Wear Analysis on Turning of Copper-Nickel 70/30 ASTM B122 Alloy under Low Initial Lubrication.Materials (Basel, Switzerland) · 2021Article
- Barrier membranes for tissue regeneration in dentistry.Biomaterial investigations in dentistry · 2021Review
- Precision Hard Turning of Ti6Al4V Using Polycrystalline Diamond Inserts: Surface Quality, Cutting Temperature and Productivity in Conventional and High-Speed Machining.Materials (Basel, Switzerland) · 2020Article
- MQL Strategies Applied in Ti-6Al-4V Alloy Milling-Comparative Analysis between Experimental Design and Artificial Neural Networks.Materials (Basel, Switzerland) · 2020Article
- Reduction of Power Consumption by Chip Breakability Control in Ti6Al4V Titanium Alloy Turning.Materials (Basel, Switzerland) · 2020Article
- Special Issue of the Manufacturing Engineering Society 2019 (SIMES-2019).Materials (Basel, Switzerland) · 2020Article
Corrections and comments
PubMed lists nothing against this paper. Absence here is not a guarantee, only a check that was made.
Authors and funding
5 authors.
Funding
No grant is acknowledged in the PubMed record.
Abstract
Titanium is one of the most interesting materials in modern manufacturing thanks to its good mechanical properties and light weight. These features make it very attractive for use in the aeronautical and aerospace industries. Important alloys, such as Ti6Al4V, are extensively used. Nevertheless, titanium alloys present several problems in machining processes. Their machinability is poor, affected by low thermal conductivity, which generates very high cutting temperatures and thermal gradients in the cutting tool. Lubricants and cutting fluids have traditionally been used to solve this problem. However, this option is unsustainable as such lubricants represent a risk to the environment and to the health of the operator due to their different chemical components. Therefore, novel, sustainable and green lubrication techniques are necessary. Dry machining is the most sustainable option. Nevertheless, difficult-to-machine materials like titanium alloys cannot be machined under these conditions, leading to very high cutting temperatures and excessive tool wear. This study is intended to describe, analyse and review the non-traditional lubrication techniques developed in turning, drilling and milling processes since 2015, including minimum quantity of lubricant, cryogenic lubrication, minimum quantity of cooling lubrication or high-pressure coolant. The aim is to provide a general overview of the recent advances in each technique for the main machining processes.
Indexed as
Identifiers
What OpenQuestion holds
Registered trials
Read under generation 80e0d062 · epoch 390. Bibliography from PubMed, PubMed Central and OpenAlex; grants from NIH RePORTER; trial links from ClinicalTrials.gov; estimates, votes and beliefs from the OpenQuestion graph.